Improving the efficiency of manufacturing parts in small-scale production through the use of additive technologies

The technological process of manufacturing parts of complex geometric shapes is characterized by high labor intensity of mechanical processing and low coefficient of material utilization, and, consequently, high cost of the resulting product. This is largely due to the fact that graded material is used as blanks for parts. As a solution to the voiced problem, it is proposed to obtain blanks by 3D printing. The advantages of using 3D printing as a method for manufacturing blanks for parts of complex shapes in small-scale production are shown.
EDN: HBJCIY, https://elibrary/hbjciy

References

[1] Akulina A.A., Nemolyakina E.A., Shchelkunov E.B. [Increasing the efficiency of “rocker” part manufacturing through the use of 3D printing]. Nauka, innovatsii i tekhnologii: ot idey k vnedreniyu. Mat. III Vseros. nauch.-prakt. konf. molodykh uchenykh [Science, Innovations and Technology: from Idea to Realization. Proc. III Russ. Sci.-Pract. Conf. of Young Scientists]. Komsomolsk-na-Amure, KnAGU Publ., 2025, pp. 3–5. (In Russ.).

[2] Lepekhina S.Yu., Sukhorukov S.I., Davydov Yu.A. Algorithm set for the operation of the control system of a robotic three-dimensional printing complex. Uchenye zapiski KnAGTU [Scientific Notes of Komsomolsk-On-Amour State Technical University], 2023, no. 1, pp. 68–75, doi: https://doi.org/10.17084/20764359-2023-65-68 (in Russ.).

[3] Vysotskiy A.A. SLM printing in engine building. Aktualnye problemy aviatsii i kosmonavtiki, 2016, no. 12, pp. 188–189. (In Russ.).

[4] Sukhorukov S.I., Godyaev A.I., Ovsyannikov A.R. Development of a control system structure for a robotic complex for 3D printing metal products. Uchenye zapiski KnAGTU [Scientific Notes of Komsomolsk-On-Amour State Technical University], 2024, no. 3, pp. 103–111. (In Russ.).

[5] Chemodurov A.N. The use of additive technologies in the production of engineering products. Izvestiya TulGU. Tekhnicheskie nauki [News of the Tula state university. Technical sciences], 2016, no. 8–2, pp. 210–217. (In Russ.).

[6] Chechuga A.O. Application of additive technologies in tool manufacturing. Izvestiya TulGU. Tekhnicheskie nauki [News of the Tula state university. Technical sciences], 2022, no. 10, pp. 452–454. (In Russ.).

[7] Bezyazychnyy V.F., Fedoseev D.V., Koretko S.E. [Surface quality of products obtained by selective laser melting]. Stankostroenie i innovatsionnoe mashinostroenie. Problemy i tochki rosta. Mat. Vseros. nauch.-tekh. konf. [Machine Tool Building and Innovative Machine Building. Problems and Growth Points. Proc. Russ. Sci.-Tech. Conf.]. Ufa, UGATU, 2019, pp. 419–423. (In Russ.).

[8] Melnikova M.A., Kolchanov D.S., Melnikov D.M. Selective laser melting: application and formation features of three-dimensional structural engineering elements. Fotonika [Photonics Russia], 2017, no. 2, pp. 42–49, doi: https://doi.org/10.22184/1993-7296.2017.62.2.42.49 (in Russ.).

[9] Eroshenko V.O., Asoyan A.R. Substantiation of the choice of 3D-forming technology of high-strength turbine blades. Problemy mashinostroeniya i avtomatizatsii [Engineering & Automation Problems], 2021, no. 1, pp. 35–39, doi: https://doi.org/10.52261/02346206_2021_1_35 (in Russ.).

[10] Ermakov D.V., Karpov I.A., Taranina Yu.A. et al. The study of the engine-flywheel housing made by additive technology. Reshetnevskie chteniya [Reshetnev Readings], 2017, vol. 1, pp. 500–501. EDN: YLYYMG (in Russ.).

[11] Ruban E.A., Akulina A.A., Shchelkunov E.B. [Improving the efficiency of parts manufacturing combining traditional and additive technologies]. Nauka, innovatsii i tekhnologii: ot idey k vnedreniyu. Mat. III Vseros. nauch.-prakt. konf. molodykh uchenykh [Science, Innovations and Technology: from Idea to Realization. Proc. III Russ. Sci.-Pract. Conf. of Young Scientists]. Komsomolsk-na-Amure, KnAGTU Publ., 2025, pp. 82–85. (In Russ.).

[12] Jiang Z., Sun J., Berto F. et al. Fatigue and fracture behavior of AlSi10Mg manufactured by selective laser melting: a review. Fizicheskaya mezomekhanika [Physical Mesomechanics], 2023, no. 2, pp. 5–29, doi: https://doi.org/10.55652/1683-805X_2023_26_2_5 (in Russ.).

[13] Dynin N.V., Zavodov A.V., Oglodkov M.S. et al. The influence of process parameters of selective laser melting on the structure of aluminum alloy Al-Si-Mg system. Trudy VIAM [Proceedings of VIAM], 2017, no. 10, doi: https://doi.org/10.18577/2307-6046-2017-0-10-1-1 (in Russ.).

[14] Popkova I.S., Zolotorevskiy V.S., Solonin A.N. Fabrication of products in aluminium and its alloys by the selective laser melting technique. Tekhnologiya legkikh splavov [Technology of Light Alloys], 2015, no. 4, pp. 14–24. (In Russ.).

[15] Nikiruy A.E., Lymar S.V., Drogovoz P.A. Time and cost of manufacturing parts by selective lasering method in the organization of precision production. Sovremennye naukoemkie tekhnologii [Modern High Technologies], 2022, no. 2, pp. 72–77, doi: https://doi.org/10.17513/snt.39040 (in Russ.).