Determination of the areas of the main operational parameters of a reciprocating hybrid power machine with regenerative heat exchange

The thermodynamic and dynamic analysis of working processes and acting forces in single-stage reciprocating compressors and pumps has been performed. It has been established that, despite the general tendency to increase the crankshaft velocity and the discharge pressure of the compressible gas and dropping liquid in reciprocating single-stage compressors and pumps, there are their optimal values, which are determined on the basis of the maximum values of the supply coefficient, indicator, volumetric and total efficiency. It is shown that these values also have limits, bounded by the oil flash point (for reciprocating compressors) and permissible stresses in the parts and assemblies of the drive mechanism (for reciprocating compressors and pumps). It was found out that for a reciprocating hybrid power machine with regenerative heat exchange, the crankshaft velocity could be taken equal to 300...700 rounds per min^-1, and the discharge pressure of the compressible gas and dropping liquid is 0.2...1.5 MPa.

References

[1] Shcherba V.E., Bolshtyanskiy A.P., Shalay V.V. et al. Nasos-kompressory. Rabochie protsessy i osnovy proektirovaniya [Pump-compressors. Working processes and design fundamentals]. Moscow, Mashinostroenie, 2013. 368 p. (In Russ.).

[2] Bolshtyanskiy A.P., Shcherba V.E., Kaygorodov S.Yu. Porshnevaya gibridnaya mashina ob’’emnogo deystviya [Piston hybrid displacement machine]. Patent RU 2592955. Appl. 03.03.2015, publ. 27.07.2016. (In Russ.).

[3] Shcherba V.E., Bolshtyanskiy A.P., Kaygorodov S.Yu. et al. Analysis of advantages of integration of displacement compressors and pumps into single unit. Vestnik mashinostroeniya, 2015, no. 12, pp. 15–19. (In Russ.).

[4] Lobov I.E., Shcherba V.E., Grigor’yev A.V. The analysis of the working processes in piston hybrid power machine using fluctuations of pressure of gas in pressure line. Omskiy nauchnyy vestnik [Omsk Scientific Bulletin], 2016, no. 2, pp. 40–44. (In Russ.).

[5] Shcherba V.E., Shalay V.V., Grigor’yev A.V. et al. Analysis of theoretical and experimental results on the effect of injection pressure in the pump section on the working processes and characteristics of a piston hybrid power machine with a slotted seal of a stepped type. Zhurnal Sibirskogo federal’nogo universiteta. Tekhnika i tekhnologii [Journal of Siberian Federal University. Engineering & Technologies], 2018, vol. 11, no. 5, pp. 591–603, doi: https://doi.org/10.17516/1999-494X-0058 (in Russ.).

[6] Shcherba V.E., Shalay V.V., Nosov E.Yu. et al. Comparative analysis of the results of experimental studies of a reciprocating piston hybrid power machine with smooth and stepped gap seals. Khimicheskoe i neftegazovoe mashinostroenie [Chemical and petroleum engineering], 2018, no. 7, pp. 25–29. (In Russ.).

[7] Shcherba V.E., Shalay V.V., Nosov E.Yu. et al. Development and research of crosshead-free piston hybrid power machine. Machines, 2021, vol. 9, no. 2, art. 32, doi: https://doi.org/10.3390/machines9020032

[8] Shcherba V.E., Shalai V.V., Tegzhanov A.S. et al. Generalized comparative analysis of crosshead-free and crosshead schemes of piston hybrid power machines. J. Mech. Sci. Technol., 2020, vol. 34, no. 12, pp. 5093–5107. URL: http://doi.org/10.1007/s12206-020-1113-4

[9] Shcherba V.E., Kuzeeva D.A., Nosov E.Yu. Nonuniform delivery rates from multicylinder pumps. Vestnik mashinostroeniya, 2016, no. 4, pp. 3–8. (In Russ.). (Eng. version: Russ. Engin. Res., 2016, vol. 36, 4, pp. 266–269, doi: https://doi.org/10.3103/S1068798X1604016X)

[10] Shcherba V.E., Nosov E.Yu., Pavlyuchenko E.A. et al. Analysis of fluid dynamics in piston hybrid energy machine with gas volume in suction. Khimicheskoe i neftegazovoe mashinostroenie [Chemical and petroleum engineering], 2016, no. 4, pp. 15–19. (In Russ.).

[11] Lobov I.E., Shcherba V.E. Analysis of the influence of efficiency of gas cooling during its compression in compressor of volume action. Khimicheskoe i neftegazovoe mashinostroenie [Chemical and petroleum engineering], 2016, no. 4, pp. 19–24.

[12] Lobov I.E., Shcherba V.E., Shalai V.V. et al. Analysis of the influence of efficiency of cooling of gas in the course of its compression in a volumetric action compressor. Chem. Petrol. Eng., 2016, vol. 52, no. 3–4, pp. 260–266, doi: https://doi.org/10.1007/s10556-016-0184-7

[13] Plastinin P.I. Porshnevye kompressory. T. 1. Teoriya i raschet [Piston engines. Vol. 1. Theory and calculation]. Moscow, Koloss Publ., 2006. 456 p. (In Russ.).

[14] Fotin B.S., ed. Porshnevye kompressory [Piston engines]. Leningrad, Mashinostroenie Publ., 1987. 372 p. (In Russ.).

[15] Bashta T.M. Ob’’emnye nasosy i gidravlicheskie dvigateli gidrosistem [Displacement pumps and hydraulic engines of hydrosysmens]. Moscow, Mashinostroenie Publ., 1974. 606 p. (In Russ.).

[16] Shcherba V.E., Nesterenko G.A., Nosov E.Yu. et al. The influence of frequency of rotation on characteristics piston the pump-compressor. Omskiy nauchnyy vestnik [Omsk Scientific Bulletin], 2011, no. 3, pp. 114–118. (In Russ.).