Determination of the Residual Stress State of High-Pressure Nozzles During Diamond Smoothing

The paper presents the results of a study that examines modelling of the polishing and hardening treatment of axisymmetric cylindrical parts such as high-pressure fittings with metal seals on the pipe and the rod. A finite element model of the diamond smoothing process was developed, which allowed one to determine the stress state in the deformation zone depending on the feed rate, tool deflection angle, pressing force, and depth of penetration into the material of the part. The analysis of the modelling results helped to identify a range of optimal modes for diamond smoothing. By using finite element modelling in ANSYS Workbench Mechanical it was possible to test those smoothing modes that were difficult to test experimentally. The study identified the most significant factors that influenced the formation of the maximum values of residual stresses in the surface layer of gate assemblies of high-pressure valves. The maximum values of compressive residual stresses, the value of which did not exceed the yield strength of the material were determined.

References

[1] Zaydes S.A. New surface plastic deformation techniques in the manufacture of machine parts. Vestnik of Nosov Magnitogorsk State Technical University, 2018, vol. 16, no. 3, pp. 129–139 (in Russ.), doi: 10.18503/1995-2732-2018-16-3-129-139

[2] Volkov A.N., Sazonov M.B., Chigrinev I.A. Research of influence of methods SPD on structure surface layer and resistance of fatigue. Vestnik of Samara University. Aerospace and mechanical engineering, 2012, no. 3(34), pp. 153–156 (in Russ.).

[3] Nikolaeva E.P., Mashukov A.N. Evaluation of residual stresses in high-pressure valve seat surfacing. Chemical and petroleum engineering, 2017, vol. 129, pp. 459–463, doi: 10.1007/s10556-017-0363-1

[4] Zaydes S.A., Emel’yanov V.N. Vliyaniye poverkhnostnogo plasticheskogo deformirovaniya na kachestvo valov [The effect of surface plastic deformation on shaft quality]. Irkutsk, IRNITU publ., 2017. 380 p.

[5] Zaydes S.A., Kyong N.K. New technological potentialities of finish-strengthening by surface plastic deformation. Science intensive technologies in mechanical engineering, 2017, no. 3(69), pp. 25–30 (in Russ.).

[6] Torbilo V.M. Calculation of the optimum force for diamond smoothing. Stanki i instrument, 1970, no. 2, pp. 25–26 (in Russ.).

[7] Nikolayeva E.P. Application the Barkhausen noises method for control the hardening of details by superficial plastic deformation. Izvestia of Samara Scientific Center of the Russian Academy of Sciences, 2013, vol. 15, no. 6(2), pp. 428–431 (in Russ.).

[8] Kuznetsov V.P., Smolin I.Yu., Dmitriyev A.I., Konovalov D.A., Makarov A.V., Kiryakov A.E., Yurovskikh A.S. Finite Element Modeling of Nanostructuring Smoothing. Physical mesomechanics, 2011, vol. 14 (6), pp. 87–97.

[9] Abul’khanov S.R., Goryainov D.S., Skuratov D.L., Shvetsov A.N. Formation of the surface layer in diamond smoothing. Russian Engineering Research, 2015, vol. 35, pp. 147–149, doi: 10.3103/S1068798X15020033

[10] Lasitsa M.A., Churankin V.G., Derkach V.V. Parameter’s Optimization of Surface Plastic Deformation Corrosion-resistant Steel by Computer Simulation. Mechanics and Mechanical Engineering, 2018, vol. 22, no. 4, pp. 991–997.

[11] Sevost’yanov A.S., Luk’yanov A.A., Bobrovskiy I.N. Modeling the processing of surface plastic deformation. Intellektual’nyy potentsial XXI veka: stupeni poznaniya, 2014, no. 23, pp. 149–153 (in Russ.).

[12] Bruyaka V.A., Fokin V.G., Soldusova E.A., Glazunova N.A., Adeyanov I.E. Inzhenernyy analiz v Ansys Workbench [Engineering Analysis at Ansys Workbench]. Pt. 1, Samara, SamSTU publ., 2010. 271 p.

[13] Zaydes S.A., Nguyen Van Khin’. The Influence of the Direction and Geometry of the Working Tool on the Stress-Strain State of Cylindrical Parts in Oscillating Burnishing. Proceedings of Higher Educational Institutions. Machine Building, 2018, no. 8, pp. 28–36 (in Russ.), doi: 10.18698/0536-1044-2018-8-28-36

[14] Chen X., Liu Y. Finite Element Modeling and Simulation with ANSYS Workbench. CRC Press, 2014. 411 p.

[15] Druyanov, B.A., Nepershin R.I. Teoriya tekhnologicheskoy plastichnosti [Theory of Technological Plasticity]. Moscow, Mashinostroyeniye publ., 1990. 271 p.