A Calculation of Characteristics of Three-Piston Pumps
Authors: Velikanov N.L., Naumov V.A. | Published: 03.12.2018 |
Published in issue: #11(704)/2018 | |
Category: Energy and Electrical Engineering | Chapter: Hydraulic Machines and Hydropneumatic Units | |
Keywords: three-piston pump, hydraulic and energy characteristics, mains pressure, supplied power |
The refinement of the calculation model for the evaluation of individual hydraulic and energy characteristics of a pumping unit is an important task, since the reliability of forecasting the amount of liquid supplied to a given point depends significantly on the accuracy of determining the characteristics of the pump in the entire range of its operation. In this regard, the authors propose an approach based on the improvement of the algorithm for calculating three-piston pumps of different manufacturers in the framework of the previously developed method of hydraulic calculation of pumping units. The calculation of three-piston pumps SVESSA and TPD-600 is considered as an example. The results of the tests performed by the manufacturer and available in public sources are chosen as the initial data for the calculations. Experimental dependences of the flow, efficiency and supplied power on the outlet pressure of the three-piston pumps 1.3T-10/20 and 1.3T-12.5/16 are presented. Calculations are performed to determine the dependence of efficiency and supplied power on pressure according to the algorithm proposed by the authors. The implementation of the recommendations for evaluating hydraulic and energy characteristics of pumping units can significantly reduce production costs when using three-piston pumps.
References
[1] Zuo Y., Wu X. A comparative study of four rod load reduction techniques for deep-rod pumping. Journal of Petroleum Exploration and Production Technology, 2018, vol. 8, is. 2, pp. 475–483, doi: 10.1007/s13202-017-0367-6
[2] Tian Y., Wang Z., Zhang L., Lu C., Ma J. A subspace learning-based feature fusion and open-set fault diagnosis approach for machinery components. Advanced Engineering Informatics, 2018, vol. 36, pp. 194–206, doi: 10.1016/j.aei.2018.04.006
[3] Koukouvinis P., Karathanassis I.K., Gavaises M. Prediction of cavitation and induced erosion inside a high-pressure fuel pump. International Journal of Engine Research, 2018, vol. 19, is. 3, pp. 360–373, doi: 10.1177/1468087417708137
[4] Gao D., Suo X., Cai Q., Wu S., Liang Y. Influences of Key Structural Parameters of Hydraulic Piston Pump on Cavitation. Zhongguo Jixie Gongcheng/China Mechanical Engineering, 2018, vol. 29, is. 4, pp. 434–440, doi: 10.3969/j.issn.1004-132X.2018.04.010
[5] Bahtizin R.N., Urazakov K.R., Ismagilov S.F., Bakirov R.I., Bashirov I.R., Kiselev A.V., Davletshin F.F. Method for calculating the plunger hanger in the cylinder of the sucker-rod pump. Oil Industry, 2018, is. 2, pp. 80–84, doi: 10.24887/0028-2448-2018-2-80-84
[6] Zyuzev A.M., Bubnov M.V. Model for Sucker-Rod Pumping Unit Operating Modes Analysis Based on SimMechanics Library. Journal of Physics: Conference Series, 2018, vol. 944, is. 1, article number 01213011, doi: 10.1088/1742-6596/944/1/012130
[7] Tong B., Yang W., Liu Q., Ye X., Shi L. Flowing and pressure-balancing characteristics of clearance field in helical grooved piston-copper sleeve pair of piston pump. Nongye Gongcheng Xuebao/Transactions of the Chinese Society of Agricultural Engineering, 2018, vol. 34, is. 2, pp. 55–63, doi: 10.11975/j.issn.1002-6819.2018.02.008
[8] Three-plunger crank pumping units and pumps. Available at: http://snz-nasos.ru/down/swessa2.pdf (accessed 31 March 2018).
[9] Velikanov N.L., Naumov V.A., Primak L.V. Determination of working point concrete pump. Mechanization of construction, 2015, no. 9, pp. 42–44 (in Russ.).
[10] Velikanov N.L., Naumov V.A., Koryagin S.I. Analysis of characteristics of plunger pumps. Vestnik mashinostroeniya, 2018, no. 3, pp. 25–27 (in Russ.).
[11] ServaGroup – Triplex & quituplex pumps. Available at: http://www.servagroup.com/triplex-quintuplex-pumps/ (accessed 01 June 2018).
[12] Khristenko A.V., Akbulatov T.O., Ishbayev G.G., Zagidullina G.V. Comparative analysis of modern methods of calculation of linear pressure losses in the pipe and annular space and its practical conclusions. Neftegazovoye delo, 2007, vol. 5, no. 1, pp. 29–36 (in Russ.).
[13] Belyayev E.F., Tsylev P.N., Shchapova I.N. Biphase multi-pole compensated asynchronous motor for oil industry. Perm journal of petroleum and mining engineering, 2017, vol. 16, no. 3, pp. 238–246, doi: 10.15593/2224-9923/2017.3.4 (in Russ.).
[14] Volkov A.V., Danilenko D.V., Ermakov D.V., Lomakin V.O. Development of 3D prototyping technology in relation to improvement of the pumps hydraulic characteristics. Pumps. Turbines. Systems, 2017, no. 3(24), pp. 70–74 (in Russ.).
[15] Chaburko P.S., Lomakin V.O., Kuleshova M.S., Baulin M.N. Complex wet end part optimization of hermetic pump with LP-TAU method. Pumps. Turbines. Systems, 2016, no. 1(18), pp. 55–61 (in Russ.).