Analysis of the product defect risk caused by the workpiece position error at the installation in a prism

The paper considers issues of assessing the risk of a product defect due to unacceptable errors in positioning surfaces during machining and caused by deviations in the dimensions of workpieces and sample used in setting up the device. Based on analyzing the published studies devoted to the workpiece positioning errors, the need was revealed to expand approaches to determining the risk of product defects by conducting machine experiments to simulate the contact between workpieces and device mounting elements, as well as to consider the joint quality indicators distribution in analyzing the position deviations. The task was set and an example of risk assessment is provided based on analytical calculation of the workpiece limiting positions, as well as the solid-state computer simulation of the technological system elements contact for the case of processing the tee-type part in a CNC milling operation on a machining center with the vertical spindle axis. Based on the results of solving the problem, examples of recommendations are provided for modifying the technological solution aimed at reducing the risk of product defects.

References

[1] Kondakov A.I., Nefedov A.A. Assessment of technology solutions succession. Izvestiya vysshikh uchebnykh zavedeniy. Mashinostroenie [BMSTU Journal of Mechanical Engineering], 2006, no. 5, pp. 65–72. (In Russ.).

[2] Mosunov A.V., Kondrashkova G.A., Bondarenkova I.V. [Approaches to choosing measuring tools for range verification of product quality]. Fundamental’nye i prikladnye nauchnye issledovaniya: innovatsionnyy potentsial razvitiya. Sb. st. mat. mezhd. nauch.-prakt. konf. [Fundamental and Applied Scientific Studies: Innovative Development Potential. Proc. Int. Sci.-Pract. Conf.]. Ufa, Vestnik nauki Publ., 2019, pp. 90–96. (In Russ.).

[3] Dal’skiy A.M., Suslov A.G., Kosnlova A.G. et al. Spravochnik tekhnologa-mashinostroitelya [Handbook of technologist mechanical engineer]. Moscow, Mashinostroenie Publ., 2003. 912 p. (In Russ.).

[4] Bolotein A.N. Determination of the workpiece position accuracy in fixture three–dimensional coordinate system. Nauka i praktika, 2019, no. 2, pp. 36–39, doi: https://doi.org/10.26160/2658–6185–2019–2–36–39 (in Russ.).

[5] Vorontsova A.N., Kozhevnikova A.A., Baev S.G. et al. Refined calculation of the adjustment size as a factor decreasing the risk of marriage. Izvestiya VolgGTU [Izvestia VSTU], 2019, no. 8, pp. 12–14. (In Russ.).

[6] Abramov F.N. Effect of workpiece locating error on accuracy of produced dimensions. STIN, 2011, no. 1, pp. 17–26. (In Russ.).

[7] Abramov F.N. Effect of prismatic workpiece locating error on location accuracy of processed surfaces. STIN, 2010, no. 2, pp. 18–22. (In Russ.).

[8] Nemytkin S.A., Poretskov A.E. Assessment of form deviation effect at calculation of parts locating limit value for such parts like rotary bodies. Vestnik SamGTU. Ser. Tekhnicheskie nauki [Vestnik of Samara State Technical University. Technical Sciences Series], 2005, no. 39, pp. 131–138. (In Russ.).

[9] Abramov F.N. Experimental study on locating error of cylindrical workpieces by two shafts on two narrow prisms. STIN, 2013, no. 3, pp. 8–12. (In Russ.).

[10] Abramov F.N. Experimental study on locating error of cylindrical workpieces by one shaft on a wide prism. STIN, 2013, no. 2, pp. 14–19. (In Russ.).

[11] Solov’yev A.I., Dzhafarova Sh.I., Savel’yeva L.V. et al. Methodology of calculating the error of locating when installing workpieces in prisms. Glavnyy mekhanik [Chief Mechanical Engineer], 2020, no. 3, pp. 58–64. (In Russ.).

[12] Savel’yeva L.V., Moskvin M.B., Tsuyshan’ L. et al. Formalization of margin of error calculation location in v–block shaft type blanks. Spravochnik. Inzhenernyy zhurnal [Handbook. An Engineering Journal with Appendix], 2020, no. 8, pp. 30–33, doi: https://doi.org/10.14489/hb.2020.08.pp.030–033 (in Russ.).

[13] Savel’yeva L.V., Solov’yev A.I., Dzhafarova Sh.I. et al. Features of determining the locating error when placing workpieces in v–block. Glavnyy mekhanik [Chief Mechanical Engineer], 2019, no. 12, pp. 47–51. (In Russ.).

[14] Pol’skiy E.A., Fil’kin D.M. Accuracy analysis of billet installation upon support prisms taking into account dimensional tie impact. Naukoemkie tekhnologii v mashinostroenii [Science Intensive Technologies in Mechanical Engineering], 2020, no. 6, pp. 21–27, doi: https://doi.org/10.30987/2223–4608–2020–6–21–27 (in Russ.).

[15] Sorokin S.V. Automated calculation system for error elements of a workpiece location in a fixture in CAD/CAM systems. Izvestiya VolGTU [Izvestia VSTU], 2017, no. 9, pp. 140–144. (In Russ.).

[16] GOST R 53442–2015. Osnovnye normy vzaimozamenyaemosti. Kharakteristiki izdeliy geometricheskie. Ustanovlenie geometricheskikh dopuskov. Dopuski formy, orientatsii, mestoraspolozheniya i bieniya [State standard GOST R 53442–2015. Basic norms of interchangeability. Geometrical product specifications. Geometrical tolerancing. Tolerances of form, orientation, location and run-out]. Moscow, Standartinform Publ., 2015. 91 p. (In Russ.).