Search
Experimental Research of Radial Deformation of the Outer Shell of Roller One-Way Clutches
| Authors: Zolotov I.A., Sharkov O.V. | Published: 23.01.2018 |
| Published in issue: #1(694)/2018 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Machine Science | |
| Keywords: one-way clutch, full-scale experiment, radial deformation, outer shell, machine drive |
A Stochastic Model of Abrasive Processing. The Dynamics of Flat Grinding
| Authors: Voronov S.A., Weidong Ma | Published: 23.01.2018 |
| Published in issue: #1(694)/2018 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Technology and Equipment for Mechanical and Physico-Technical Processing | |
| Keywords: stochastic model, dynamics, grinding, cutting forces, vibrations, random geometry, abrasive grains, texture, machined surface |
Kinetic Analysis of the Mechanism of Self-Induced Vibrations of the Mass Concentration of Dispersed-and-Solidphase Particles into a Hydro-Ultrajet
| Authors: Barzov A.A., Veltishchev V.V., Galinovsky A.L., Mugla D.R. | Published: 24.01.2018 |
| Published in issue: #1(694)/2018 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Manufacturing Engineering | |
| Keywords: abrasive, focusing abrasive-liquid nozzle, hydro-ultrajet, ejection, hydroabrasive processing, hydroabrasive cutting |
Calculation of the Cutting Forces When Processing Plastic Materials with a Wide Range of Thicknesses of the Cutting Layer
| Authors: Grubyi S.V. | Published: 21.02.2018 |
| Published in issue: #2(695)/2018 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Technology and Equipment for Mechanical and Physico-Technical Processing | |
| Keywords: chip formation parameters, shear angle, chip reduction coefficient, relative shear, cutting force, roughness parameters |
The Research of Geometry and Qualitative Indicators of a Gear Pump with Internal Involute Gearing
| Authors: Tarabarin V.B., Tarabarina Z.I. | Published: 21.02.2018 |
| Published in issue: #2(695)/2018 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Theory of Mechanisms and Machines | |
| Keywords: gear pumps, internal involute gearing, calculation of geometry of engagement, boundary conditions, qualitative indicators, blocking contours |
Mechanical Properties of Woven Metal Mesh Used for Manufacturing Porous Net Materials from 12Kh18N10T Steel
| Authors: Tretyakov A.F. | Published: 21.02.2018 |
| Published in issue: #2(695)/2018 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Welding, Allied Processes and Technologies | |
| Keywords: porous net materials, woven metal mesh, mechanical properties, stress-strain diagram, percent reduction, pressure welding |
Ultrasonic Welding of Caprolon B Centrifugal Pump Impellers
| Authors: Volkov S.S., Nerovnyy V.M., Stankevich I.V. | Published: 21.02.2018 |
| Published in issue: #2(695)/2018 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Welding, Allied Processes and Technologies | |
| Keywords: ultrasonic welding, rivet joint, centrifugal pump impeller, oscillation amplitude of the waveguide, cyclic deformation, static welding pressure |
The Influence of New Kinematics of the Rolling Roller on the Quality of the Hardened Layer Under Surface Plastic Deformation
| Authors: Zaides S.A., Ngo Cao Cuong | Published: 21.02.2018 |
| Published in issue: #2(695)/2018 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Technology and Equipment for Mechanical and Physico-Technical Processing | |
| Keywords: two-radial roller, deformation hardening, surface plastic deformation, surface layer quality, roughness, hardness, residual stresses |
Creating Rational Conditions for Turning Surfaces of Dissimilar Structural Materials by Brittle Superhard Cutters
| Authors: Kudryashov E.A., Smirnov I.M. | Published: 21.02.2018 |
| Published in issue: #2(695)/2018 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Technology and Equipment for Mechanical and Physico-Technical Processing | |
| Keywords: intermittent surface, damping cutter, composite cutting material, rational contact conditions, combination of dissimilar materials, tool durability |
Profiling the Flutes in Thread-Milling Cutters
| Authors: Malkov O.V., Pavlyuchenkov I.A., Kozyar V.N. | Published: 30.03.2018 |
| Published in issue: #3(696)/2018 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Technology and Equipment for Mechanical and Physico-Technical Processing | |
| Keywords: helical flute, thread-milling cutter, profiling of the flutes, generation of geometry of the end section, grinding of the flutes |