Search
Forging as a way to improve the quality and turning of specialty steels
| Authors: Golovkin P.A. | Published: 16.09.2024 |
| Published in issue: #9(774)/2024 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Manufacturing Engineering | |
| Keywords: special steels, deformation rate, rod end, material structure, surface quality, cutter loading |
Influence of the tool vibration on the part surface in longitudinal turning
| Authors: Zakovorotny V.L., Gvindzhiliya V.E. | Published: 17.09.2024 |
| Published in issue: #9(774)/2024 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Technology and Equipment for Mechanical and Physico-Technical Processing | |
| Keywords: dynamic cutting system, vibration disturbances, surface geometric characteristics |
Studying the extended Kalman filter — adaptive digital filter system operation as the non-stationary signal filter
| Authors: Bezmen P.A. | Published: 27.09.2024 |
| Published in issue: #10(775)/2024 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Robots, Mechatronics and Robotic Systems | |
| Keywords: non-stationary signal, extended Kalman filter, adaptive digital filter, robotic device |
Energy efficiency of a hydraulic system with the centrifugal pump
| Authors: Velikanov N.L., Naumov V.A. | Published: 03.10.2024 |
| Published in issue: #10(775)/2024 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Hydraulic Machines, Vacuum, Compressor Technology, Hydraulic and Pneumatic Systems | |
| Keywords: specific energy costs, centrifugal pump, hydraulic power, energy efficiency |
Influence of the upper-rotor device with axial and inclined grooves on the axial-flow pump cavitation characteristics
| Authors: Shoronov S.V., Kazennov I.S., Istomin E.A. | Published: 04.10.2024 |
| Published in issue: #10(775)/2024 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Hydraulic Machines, Vacuum, Compressor Technology, Hydraulic and Pneumatic Systems | |
| Keywords: axial-flow pump, upper-rotor device, axial grooves, inclined upper-rotor grooves, cavitation characteristics, pressure characteristic delay |
Plane problem in a vibration isolation system with the active dynamic vibration damper
| Authors: Buryan Yu.A., Shalai V.V., Sitnikov D.V., Buryan A.A. | Published: 07.10.2024 |
| Published in issue: #10(775)/2024 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Machine Science | |
| Keywords: active dynamic vibration damper, vibration isolation system, vibration protection, angular vibrations, frequency characteristics |
Structural analysis of a parallel structure mechanism with six degrees of freedom and the truncated cone base
| Authors: Sokolovskii S.V. | Published: 07.10.2024 |
| Published in issue: #10(775)/2024 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Robots, Mechatronics and Robotic Systems | |
| Keywords: spatial mechanism, parallel structure, truncated cone, number of degrees of freedom |
Organizing the group robotic UAV systems operation based on the targeted technological effects
| Authors: Mescheryakov A.K., Potyupkin A.Y. | Published: 11.10.2024 |
| Published in issue: #10(775)/2024 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Robots, Mechatronics and Robotic Systems | |
| Keywords: multi-agent systems, UAV, employment scenario, continuity effect, situational management |
Selection of the optimal flow passage parameters for the Turo-type torque flow pump
| Authors: Svoboda D.G., Klimovich V.I., Zharkovskii A.A., Klyuyev A.S., Gorbatov D.A. | Published: 11.10.2024 |
| Published in issue: #10(775)/2024 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Hydraulic Machines, Vacuum, Compressor Technology, Hydraulic and Pneumatic Systems | |
| Keywords: torque flow pump, flow passage, design parameters, geometric characteristics optimization, integral parameters, energy characteristics |
Developing the nanostructure coating composition and structure for cutting tools based on the quantum mechanical simulation
| Authors: Kabaldin Y.G., Bashkov A.A., Ivanov S.V. | Published: 11.10.2024 |
| Published in issue: #10(775)/2024 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Manufacturing Engineering | |
| Keywords: wear-resistant coating, cutting tool, carbide, quantum mechanical computation, refractory compounds Fermi level, adhesion strength |