Search
Checking calculations of stresses in gears using ANSYS
| Authors: Karatushin S.I., Bildyuk N.A., Pleschanova Y.A., Bokuchava P.N. | Published: 02.04.2015 |
| Published in issue: #3(660)/2015 | |
| Category: Technology and Process Machines | |
| Keywords: residual stress, force calculation, cementation, bending and contact strength, ANSYS |
Improving the performance of cast housings and stationary base members at the production stage
| Authors: Yagopolskiy A.G., Kutsaya A.Y., Savokhina O.M., Zaytsev A.N. | Published: 02.04.2015 |
| Published in issue: #3(660)/2015 | |
| Category: Technology and Process Machines | |
| Keywords: technological machines, casting defects, stationary base member, diagnostic algorithm, performance |
Analysis of cutting torques during tapping with internal chip placement using ionized air as a cool-ing and lubricating fluid
| Authors: Litvinenko A.V., Zubkov N.N. | Published: 02.04.2015 |
| Published in issue: #3(660)/2015 | |
| Category: Technology and Process Machines | |
| Keywords: thread cutting, tap, ionized air, cooling, cutting torque, reversal torque |
Shear test experiments for determination of sheet materials hardening curves
| Authors: Vlasov A.V., Shitikov A.A. | Published: 17.04.2015 |
| Published in issue: #4(661)/2015 | |
| Category: Technology and Process Machines | |
| Keywords: experiment, sheet materials, shear, cold deformation, hardening curve |
Run time and cutting capacity for creep-feed grinding by cone wheel
| Authors: Nosenko V.A., Nosenko V.A., Zotova S.A., Kremenetsky L.L. | Published: 17.04.2015 |
| Published in issue: #4(661)/2015 | |
| Category: Technology and Process Machines | |
| Keywords: creep-feed grinding, mathematic modeling, run time, cutting capacity, stages of grinding |
Actuators in automatic control systems of compressor and vacuum machines
| Authors: Prudnikov S.N., Chernyshev I.A. | Published: 06.05.2015 |
| Published in issue: #5(662)/2015 | |
| Category: Technology and Process Machines | |
| Keywords: pneumatic and hydraulic drive, torque, valve, shutter, actuator |
Probability estimation of weld seam defect formation and calculation of tolerances for narrow gap arc welding parameters
| Authors: Sholokhov M.A., Erofeev V.A., Poloskov S.I. | Published: 06.05.2015 |
| Published in issue: #5(662)/2015 | |
| Category: Technology and Process Machines | |
| Keywords: arc welding, narrow gap, weld seam defects formation, welding parameters, probability of defects formation |
The relationship between the grain width of black silicon carbide grinding powder and the test sieve mesh size
| Authors: Nosenko V.A., Aleksandrov A.A. | Published: 06.05.2015 |
| Published in issue: #5(662)/2015 | |
| Category: Technology and Process Machines | |
| Keywords: grinding powder, silicon carbide, grain width, mesh size |
Experimental study of chip shrinkage for radius rear surface turning tools
| Authors: Filippov A.V., Filippova E.O. | Published: 16.06.2015 |
| Published in issue: #6(663)/2015 | |
| Category: Technology and Process Machines | |
| Keywords: chip shrinkage, oblique cutting, deformation |
Experimental research of stress state of feed in wedge-shaped workspace of pellet mill
| Authors: Kovrikov I.T., Kirilenko A.S. | Published: 16.06.2015 |
| Published in issue: #6(663)/2015 | |
| Category: Technology and Process Machines | |
| Keywords: pellet mill, ring die, press roller, lateral extrusion, closed wedge-shaped workspace, restrictive ring, tensometric element |